Wilwood MasterCylinder No: 260-9921 Manuel d'utilisateur télécharger pdf

4700 Calle Bolero • Camarillo, CA 93012 Phone 805 / 388-1188 • Fax 805 / 388-4938

WARNING • NOT A LINE LOCK • NOT FOR STREET USE

THIS DEVICE IS INTENDED FOR SPECIALIZED RACING USE ONLY. READ INSTRUCTIONS AND ALL WARNINGS CAREFULLY.

INSTALLATION OF THIS COMPONENT SHOULD ONL

Y BE PERFORMED BY PERSONS EXPERIENCED IN THE INSTALLATION AND

PROPER OPERATION OF DISC BRAKE SYSTEMS. IT IS THE RESPONSIBILITY OF THE PERSON INSTALLING ANY BRAKE

COMPONENT OR KIT TO DETERMINE THE SUITABILITY OF THE COMPONENT OR KIT FOR THAT PARTICULAR APPLICATION.

RACING EQUIPMENT AND BRAKES MUST BE MAINTAINED AND SHOULD BE CHECKED REGULARLY FOR FATIGUE, DAMAGE

AND WEAR.

DS-572 REV DATE: 03-28-07

LINE SHUT-OFF VALVE

P/N 260-9921

GENERAL INFORMATION:

This valve can be used as a brake shut-off. When energized, the valve will block

pressure from reaching downstream. The valve does not prevent fluid from returning to

the master cylinder. This eliminates the possibility of trapping pressure when activating

the valve.

INSTALLATION INSTRUCTIONS:

Mounting/Routing: Position the brake shut-off valve between the master cylinder and

the caliper to be shut-off. Mount securely with the bleed screw in the up position utilizing

the mounting slots in the bracket using two mounting screws (not provided). The in/out

brake shut-off ports are 1/8-27 NPT threads. An adapter may be required from the port

fittings of the unit (included) to the brake line tubing depending upon the application.

Run a brake line from the master cylinder to the “IN” port of the brake shut-off. Run

another line from the “OUT" port of the brake shut-off to the caliper you want to control.

The brake shut-off may be bled through the top bleed screw if necessary.

Wiring: The lead wires should be connected to a 12 volt, 5 amp (recommended) fused

power source through a toggle switch. Always be sure to switch off the power to the

line shut-off when the unit is not needed

1.67 (42,4)

2.16 (54,9)

1.15

(29,2)

1.67 (42,5)

2.00 (50,8)

1.00 (25,4) .65 (16,5)

1.00

(25,4)

1.63

(41,3)

4.28

(108,7)

3.09 (78,5)

2 PLACES

.38 (9,5)

#18 x 24" LONG

(2 WIRES)

.20 (5,1) WD x

.26 (6,6) LG

MOUNT SLOT

.26 (6,6) DIA

MOUNT HOLE

1/8-27 NPT

INLET

1/8-27 NPT

OUTLET

.50

(12,7)

.50

(12,7)

1.01

(25,5)

3.63

(92,1)

OUT

WARNING

NOT A LINE LOCK

This device is intended for

specialized racing use

only. Read instructions

and all warnings carefully

NOT FOR STREET USE

Line Shut-off, Mounting Dimensions

Wilwood’s Line Shut-off Valve

FOR OFF ROAD USE ONLY

BEFORE OPERATING VEHICLE, TEST THE BRAKES UNDER CONTROLLED CONDITIONS. MAKE SEVERAL STOPS IN A SAFE AREA FROM LOW SPEEDS AND ONLY

GRADUALLY

WORK UP TO HIGHER SPEEDS. DO NOT RACE ON UNTESTED BRAKES! ALWAYS UTILIZE SAFETY RESTRAINT SYSTEMS WHILE OPERATING VEHICLE.

IMPORTANT: READ DISCLAIMER OF WARRANTY INCLUDED WITH THE COMPONENTS.

LINE SHUT-OFF VALVE 1
P/N 260-9921 1

Résumé du contenu

Page 1 - P/N 260-9921

4700 Calle Bolero • Camarillo, CA 93012 Phone 805 / 388-1188 • Fax 805 / 388-4938WARNING • NOT A LINE LOCK • NOT FOR STREET

Commentaires sur ces manuels

Pas de commentaire

Wilwood MasterCylinder No: 260-9921 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour les vélos Wilwood MasterCylinder No: 260-9921. Wilwood MasterCylinder No: 260-9921 User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour les vélos Wilwood MasterCylinder No: 260-9921